技術要求：
1、安裝方式：掛壁式。
2、外形尺寸：550（高）×400（寬）×204（厚）（mm）
3、防護等級：IP44防濺式；
4、工作電壓：18V~36V；
5、最大輸出電流：15A
6、正常工作條件：
Δ環境溫度-25_70℃；
Δ相對濕度：≤98%RH；
Δ大氣壓力：86kpa~106kpa。
Δ振動：2~25Hz時振幅為±1.6mm;13.2~80Hz;加速度±40a/s2
Δ有船舶正常營運所產生的振動和沖擊的場所。
7、箱體應符合IP44的規定，能承受任何方向的濺水而無有害影響。
8、通訊方式：RS485，CAN總線。
9、控制箱采用7寸彩色液晶屏顯示發動機的轉速、油壓、水溫、油溫，以及電瓶電壓，發動機運行時間，當發生超速預警、油壓低、水溫高、油溫高電瓶電壓時，控制箱發出聲光報警提示，當發生超速停機、油壓過低、水溫過高時，控制箱發出聲光報警并使發動機緊急停機動作。
10、控制箱面板上設置有：啟動按鍵、消音、復位、自檢按鈕、停機按鍵、轉速調節旋鈕、電源開關、本地/遙控/自動、怠速/額定。
11、控制箱箱內預留有：超速報警延伸、油壓低報警延伸、水溫高報警延伸、油溫高報警延伸、電源故障報警延伸、綜合報警、運行信號延伸，轉速微調、緊急停機輸入，自啟動輸入、自停機輸入接口。
12、對外留有一路RS485通訊接口以及一路備用電源輸入接口。
13、控制箱有三次啟動失敗報警功能，三次自啟動時間順序：啟動時間7秒，間隔時間為8秒，三次啟動時間應為45秒內完成；當機組在自動狀態時，機組檢測到主電源故障（船舶主配電板提供的無源、常開觸點，閉合時工作），機組自動完成下列動作：啟動、升速、發出允許合閘信號（無源、常開觸點，閉合時工作），從機組檢測到主電源故障信號到輸出允許合閘信號的時間不大于45秒。當機組檢測到主電源恢復正常后，機組自動完成下列動作：發出分閘信號、降速、冷機運轉120秒后停機。
14、主要特點：
①控制器8607擁有19路輸入，19路輸出，3路電壓型，3路電流型，4路電阻型模擬量口，可根據應用場景選擇不同的配置，自定義顯示界面，通用性強。
②ECU故障碼可以自動翻譯成中文。
③電控機組，當ECU不帶下垂功能，控制器可彌補ECU，實現下垂功能，解決船上并機問題。
technical requirement:
1. Installationmethod:Wall mounted.
2. Externaldimensions: 550 (H) x 400 (W) x 204 (T) (mm)
3. Protection level: IP44 splash-prooftype;
4. Operating voltage: 18V~36V;
5. Maximum output current: 15A
6. Normal working conditions:
Ambient temperature-25_70℃;
Relative humidity: 98%RH;
Atmospheric pressure: 86kpa~106kpa.
Vibration: 2~25Hz amplitude is ± 1.6mm; 13.2~80Hz; acceleration is ± 40a / s2
Places where vibration and impact arisefrom the normal operation of the ship.
7. The box shall comply with the provisionsof IP44 and can withstand the splashing water in any direction without harmfuleffects.
8. Communication mode: RS485, CAN bus.
9. The control box adopts 7-inch color LCDscreen shows the engine speed, oil pressure, water temperature, oiltemperature, battery voltage, engine running time, when overspeed warning, lowoil pressure, water temperature, oil temperature battery voltage, the controlbox sound and light alarm prompt, when overspeed shutdown, low oil pressure,water temperature, the control box alarm and make the engine emergencyshutdown.
10. The control box panel has: startbutton, noise elimination, reset, self-check button, stop button, speedadjustment knob, power switch, local / remote control / automatic, idle /rating.
11. The control box includes: overspeedalarm, oil pressure alarm, high water temperature alarm, oil temperature alarm,power fault alarm, comprehensive alarm, operation signal extension, speed finetuning, emergency stop input, self-start input, self-stop input interface.
12. There is an external road RS485communication interface and a road backup power input interface.
13.The control box has three failed startalarm functions, and the sequence of the three self start times is: start timeof 7 seconds, interval time of 8 seconds, and the three start times should becompleted within 45 seconds; When the unit is in automatic mode, it detects afault in the main power supply (passive and normally open contacts provided bythe ship's main distribution board, working when closed), and the unitautomatically completes the following actions: start, speed up, and issue anallowable closing signal (passive and normally open contacts, working whenclosed). The time from the detection of the main power supply fault signal bythe unit to the output of the allowable closing signal shall not exceed 45seconds. When the unit detects that the main power supply has returned tonormal, it automatically completes the following actions: issuing a tripsignal, reducing speed, and stopping the chiller after running for 120 seconds.
14. Main features:
① Controller 8607 has 19 inputs, 19 outputs, 3 voltage type, 3current type, and 4 resistance type analog ports.Different configurations canbe selected according to the application scenario, and the display interfacecan be customized, making it highly versatile
② ECU fault codes can be automatically translated into Chinese
③ Electronic control unit, when the ECU does not have droop function,the controller can compensate for the ECU, achieve droop function, and solvethe problem of parallel operation on board.
